i can`t install driver RTL8814au in fedora28 (solved)
i am trying to install a edup usb wireless adapter model EP-AC1621
every thing went well,exept building ,see command sudo dkms build -m rtl8814au -v 4.3.21below.
the command should work with the 4.15kernel. i use 4.19.0-0.rc0.git9.2.fc30.x8664 now.
My working network,with driver=rtl8192cu workes untill the 4.18kernel so i have to startup with kernel 4.18 for internet access.
I cant find a solution yet for this 4.19 kernel .
hope somebody has find a solution,thanks in advance.
iwconfig
enp2s0 no wireless extensions.
wlp0s19f2u1 IEEE 802.11bgn ESSID:"HT37Pro" Nickname:"<WIFI@REALTEK>"
Mode:Managed Frequency:2.417 GHz Access Point: 02:03:AC:1F:6F:13
Bit Rate:72.2 Mb/s Sensitivity:0/0
Retry:off RTS thr:off Fragment thr:off
Power Management:off
Link Quality=100/100 Signal level=94/100 Noise level=0/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
virbr0-nic no wireless extensions.
virbr0 no wireless extensions.
lo no wireless extensions.
virbr0-nic is the edup adapter
lshw -C network
*-network
description: Ethernet interface
product: AR8151 v2.0 Gigabit Ethernet
vendor: Qualcomm Atheros
physical id: 0
bus info: pci@0000:02:00.0
logical name: enp2s0
version: c0
serial: d0:50:99:92:4c:85
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair
resources: irq:24 memory:febc0000-febfffff ioport:e800(size=128)
*-network:0
description: Wireless interface
physical id: 1
bus info: usb@2:1
logical name: wlp0s19f2u1
serial: 60:e3:27:1c:9c:bf
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=rtl8192cu ip=192.168.43.222 multicast=yes wireless=IEEE 802.11bgn
*-network:1 DISABLED
description: Ethernet interface
physical id: 2
logical name: virbr0-nic
serial: 52:54:00:a7:2a:16
size: 10Mbit/s
capabilities: ethernet physical
configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full link=no multicast=yes port=twisted pair speed=10Mbit/s
sudo dkms build -m rtl8814au -v 4.3.21
Kernel preparation unnecessary for this kernel. Skipping...
Building module:
cleaning build area...
'make'..............(bad exit status: 2)
Error! Bad return status for module build on kernel: 4.19.0-0.rc0.git9.2.fc30.x86_64 (x86_64)
Consult /var/lib/dkms/rtl8814au/4.3.21/build/make.log for more information.
DKMS make.log for rtl8814AU-1.0 for kernel 4.19.0-0.rc0.git9.2.fc30.x86_64 (x86_64)
zo 26 aug 2018 20:11:05 CEST
make ARCH=x86_64 CROSS_COMPILE= -C /lib/modules/4.19.0-0.rc0.git9.2.fc30.x86_64/build M=/var/lib/dkms/rtl8814AU/1.0/build modules
make[1]: Map '/usr/src/kernels/4.19.0-0.rc0.git9.2.fc30.x86_64' wordt binnengegaan
CC [M] /var ...
Same problem with kernel >= 4.15 as reported here (a different realtek chip). Google a bit to see if there are patches around, if you have some C programming skills you can try to adapt the patch in the link above.
Thanks,i will try that
I am also trying the same thing and install wireless adapter model EP-AC1621 but I can't, after that, I take a help of Hp Support Assistant to solve out my issue but I can't do the thing properly, can anyone guide me?